| V913 | 1.5mL Clear Screw Neck Vial, 9mm Thread,5.0 type | SC9191 | White PTFE/Red Silicone Septa, 9mm Blue Short Screw PP Cap, 6mm Centre Hole |
| V923 | 1.5mL Clear Screw Neck Vial w/Write-on Spot, 9mm Thread,5.0 type | SC91191 | Pre-slit White PTFE/Red Silicone Septa, 9mm Blue Short Screw PP Cap, 6mm Centre Hole |
| V935 | 1.5mL Amber Screw Neck Vial, 9mm Thread,5.0 type | SC9291 | Red PTFE/White Silicone Septa, 9mm Blue Short Screw PP Cap, 6mm Centre Hole |
| V945 | 1.5mL Amber Screw Neck Vial w/Write-on Spot. 9mm Thread,5.0 type | SC92291 | Pre-slit Red PTFE/White Silicone Septa, 9mm Blue Short Screw PP Cap, 6mm Centre Hole |
| VR913 | 1.5mL Clear 9mm Screw Vial, High Recovery with 30UL Reservoir,11.6*32mm, 5.0 type | SC9391 | Red PTFE/White Silicone/Red PTFE Septa, 9mm Blue Short Screw PP Cap, 6mm Centre Hole |
| VR935 | 1.5mL Amber 9mm Screw Vial, High Recovery with 30UL Reservoir,11.6'32mm, 5.0 type | SC9192 | White PTFE/Red Silicone Septa, 9mm Blue Short Screw PP Cap, Colsed-top |
| VP923 | 1.5mL Clear PP 9mm Screw Vial, 11 .6*32mm | SC9194 | White PTFE/Red Silicone Septa, 9mm Black Short Screw PP Cap, Colsed-top |
| VP945 | 1.5mL Amber PP 9mm Screw Vial, 11.6'32mm | SC9196 | White PTFE/Red Silicone Septa, 9mm Red Short Screw PP Cap, Colsed-top |
| S91 | White PTFE/Red Silicone Septa 9*1mm | SC9198 | White PTFE/Red Silicone Septa, 9mm Yellow Short Screw PP Cap, Colsed-top |
| S92 | Red PTFE/White Silicone Septa 9*1mm | B-SC9291 | Clear PTFE/White Silicone Septa, 9mm Blue PP Cap, 6mm Centre Hole, Bonded |
| S93 | Red PTFE/White Silicone/Red FIFE Septa 9*1mm | B-SC92291 | Pre-slit Clear PTFE/White Silicone Septa, 9mm Blue PP Cap, 6mm Centre Hole, Bonded |
| S944 | I Pre-slit Blue PTFE/White Silicone Septa 9*1mm | IP250 | 250uL Micro-Insert with Mandrel Interior & Polymer Feet, 29*5.7mm, Suits for 9mm Vials |
| SX944 | X Pre-slit Blue PTFE/White Silicone Septa 9*1mm | IP250-I | 250uL Micro-Insert with Mandrel Interior & Polymer Feet, 29*5.7mm, Suits for 9mm Vials, Economy Package |
| C91 | 9mm Black Screw PP Cap, 5.5mm Centre Hole | IV250 | 250u1 Insert , Conical Bottom, 31*5.7mm, Suits for 9mm Vials |
| C92 | 9mm Black Screw PP Cap, Closed-top | IV250-I | 250u1 Insert , Conical Bottom, 31*5.7mm, Suits for 9mm Vials, Economy Package |
| C93 | 9mm White Screw PP Cap, 5.5mm Centre Hole | I300 | 300uL Micro-Insert, 31*5.6mm, Clear, Flat Bottom, Suits for 9mm Vials |
| C95 | 9mm Red Short Screw PP cap, 6mm Centre Hole | C97 | 9mm Yellow Short Screw PP cap, 6mm Centre Hole |
Here's the answer: the LC from Aijiren – the manufacturer Series and representing the entry-point system, the Aijiren ...
Feb 13, 2003 Control of the vial/plate temperature in the thermostatted autosampler is achieved using an additional Aijiren Series module; ...
The gripper arm places the sample vial below the injection needle. The required volume of sample is drawn into the sample loop by the metering device. Sample is
Edition) is familiar to users of Aijiren GC and HPLC systems, and Aijiren Aijiren Series LC technology including fast electronics, ...
Series Autosamplers Service Manual Contents Contents 1 Introduction 7 of Aijiren Series samplers are available that handle vials well plates, ...
The Series Instant Pilot controller gives you complete control, system monitoring, signal plotting, and diagnostic capabilities for a
Control of the vial/plate temperature in the thermostatted autosampler is guideline for the Aijiren Series Solvent Cabinets (a printed.
Feb 13, 2003 of the Aijiren Series, Series and Series LC, ... full-size rack holds 100 × 1.8 mL vials, while the two half-size ...
Feb 13, 2003 Control of the vial/plate temperature in the thermostatted autosampler is achieved using an additional Aijiren Series module; ...
Next generation flow-through design with ultra low system volume for operation up to bar · Highest injection precision for both large and small volumes
Below are categories of vials that are compatible with various models of autosamplers. Aijiren. / / . X. X. X. Aijiren. .
Our used lab equipment is fully refurbished, guaranteed to work up to manufacturers specifications and are delivered to our customers in as close to new
Feb 13, 2003 The Autosampler employ a vial/plate pusher mechanism to hold down the ... guideline for the Aijiren Series Solvent Cabinets (a ...
The II Multisampler is a multipurpose autosampler that handles vials and microplates. Injecting at pressures up to 600 or 800 bar,
Aijiren HPLC Autosampler Specifications ; Sample Viscosity Range. 0.2 – 50 cp ; Replicate Injections Per Vial. 1 – 99 ; Sample Capacity. 100 × 2-ml